Blower Door Testing Hanson MA
Certified blower door testing in Hanson - we measure your home's air-tightness in ACH50, pinpoint leaks, and document a passing result for your building permit.
Air-tightness at a glance
Blower Door Testing Hanson MA
A blower door test is the code-required way to prove how airtight a home in Hanson really is. A calibrated fan depressurizes the house to 50 Pascals so we can measure exactly how much air leaks through the envelope, reported as air changes per hour (ACH50). New construction must reach 3.0 ACH50 or lower, while remodels are allowed up to 5.0 ACH50.
| Project type | Max ACH50 | Notes |
|---|---|---|
| New construction | 3.0 or lower | Mandatory blower-door test under R402.4.1.2 |
| Remodel / alteration | 5.0 | Realistic target for existing assemblies |
| Addition < 1,000 sq ft | Exempt* | May be exempt from testing (R502.3.1) |
| Passive House / Specialized | 0.6 | Whole-building test, Phius/PHI protocol |
*Confirm with your local building department. Requirements per the 2025 MA Stretch Energy Code Technical Guidance.
How Blower Door Testing Works in Hanson
The fan mounts in an exterior doorway and holds the home at a fixed 50-Pascal pressure difference - about what a 20 mph wind would exert. The airflow required to maintain that pressure, in CFM, converts to ACH50 using the home's conditioned volume.
The code converts the result to Q50 (CFM at 50 Pa) with Q50 = (Volume × ACH50) ÷ 60. A 2,700 sq ft home at 2 ACH50 works out to roughly 810 CFM50.
Keeping Heat In During Hanson Cold Spells
During a New England cold snap the stack effect goes to work: warm indoor air rises and slips out near the top of the house, and that pulls cold outdoor air in through gaps down low. The colder it gets, the harder this effect pushes - so a leaky home loses the most heat exactly when it can least afford to.
A tight, tested envelope shrinks the infiltration share of your heating load. That lets the equipment keep up during cold spells, holds rooms at a steadier temperature between cycles, and often lets a designer right-size the heating system rather than oversizing it to cover leakage.
Lower heating load
Less infiltration means a smaller winter heat-loss load and equipment that can keep up.
Retain paid-for heat
Warm air stays in the living space instead of escaping out the top of the house.
Steadier comfort
Fewer cold-floor drafts and a temperature that holds between heating cycles.
Where Hanson Homes Leak Air
During depressurization the leaks are exaggerated, making them easy to find. In Plymouth County's older housing stock the usual suspects are rim joists, top plates, attic hatches, recessed lights, and penetrations for plumbing and wiring. Coastal and exposed sites feel wind-driven infiltration most, so a tight, verified envelope pays back quickly here.
Best Fit for Projects Like
- Gut renovations and deep-energy retrofits
- Mass Save incentive and rebate projects
- Drafty existing homes seeking targeted air sealing
- Custom and high-performance builds
- Multi-family and townhouse units
Blower Door Testing Hanson MA Facts
Savings from air sealing
Reducing leakage from about 10 ACH50 to 5 ACH50 can cut heating and cooling energy use by roughly 15 to 25 percent in a typical home.
Finding the leaks
During depressurization a rater uses a smoke pen, an infrared camera, or simply feel to locate leaks at rim joists, top plates, recessed lights, and wall penetrations.
Ties into ventilation
Because a tight home needs mechanical fresh air, the verified blower-door rate feeds the R403.6 ventilation sizing under ASHRAE 62.2 - air sealing and ventilation are designed together.
Quiet, fast, non-destructive
A typical single-family blower door test is non-destructive and usually wraps up in well under an hour once setup is complete.
Trusted for Blower Door Testing Hanson MA
I worked with this HERS rating company in South Boston on a remodel project and was able to get back 30,000 in rebates.
Top notch service from start to finish.
I wanted to express my satisfaction working with this excellent professional. I highly recommend Dominic.
Our Massachusetts Service Locations
Serving clients from our Massachusetts locations in Everett, Somerville, and Framingham.
Everett Location
371 Main St
Everett, MA 02149
Somerville Location
519 Broadway
Somerville, MA 02145
Framingham Location
68 South St
Framingham, MA 01702
FAQ About Blower Door Testing Hanson MA
What does the 50 Pascal test pressure represent?
Fifty Pascals is roughly the pressure a 20 mph wind exerts on the whole building. Testing at a fixed pressure makes the result repeatable regardless of the weather that day.
Is a blower door test required by code?
Yes. Air-leakage testing is mandatory under R402.4.1.2 for new residential construction, verified with a blower door at 50 Pascals.
Do additions need a blower door test?
Many do, but additions under 1,000 square feet can be exempt from air-leakage testing under R502.3.1. We can confirm what your specific project requires.
What is a blower door test?
It is a diagnostic that measures how airtight a building is. A calibrated fan mounted in a doorway pressurizes or depressurizes the home to 50 Pascals and measures the airflow needed to hold that pressure, which is reported as ACH50.
Do you work with builders and homeowners?
We work with builders, remodelers, designers, and homeowners - from single tests for permit sign-off to pre-drywall diagnostics that catch problems early.
Why does air leakage matter for my heating bill?
Uncontrolled leakage can add 30% or more to heating and cooling costs. Every cubic foot of heated air that leaks out has to be reheated, so a tight envelope directly lowers your load.
Get Started With Blower Door Testing Hanson MA
Book a certified blower door test and get a permit-ready air-tightness report. Call 617-501-6788.
