Burlington Spray Foam & Insulation
Across Burlington, homes range from a mix of colonials, capes, ranches, and newer construction. Spray foam insulation seals and insulates in a single step, so your Burlington project gets a tighter, more comfortable building envelope with lower energy bills.
Which Spray Foam Is Right for Your Project?
Spray foam comes in two families, and the right choice shapes both performance and cost on a Burlington project.
Closed-Cell Spray Foam
Dense and rigid at roughly R-6 to R-7 per inch — the highest R-value of common insulation. It also acts as an air and vapor barrier and adds stiffness, making it ideal for rim joists, basements, crawlspaces, and roof decks in Burlington homes.
Open-Cell Spray Foam
Lighter and vapor-permeable at about R-3.5 to R-3.8 per inch. It expands to fill irregular cavities, seals air leaks, and dampens sound — a strong choice for interior walls and attics where drying potential matters.
Insulation Types & R-Values Per Inch
R-value measures resistance to heat flow — higher is better. Here is how the insulation materials used on Burlington, Burlington projects compare per inch of thickness.
Open-cell spray foam
Lighter and vapor-permeable; expands fully to fill irregular cavities, seals air leaks and dampens sound. A common choice for interior walls and vented attics.
Mineral wool (rock wool)
Dense, naturally fire-resistant and water-repellent batts or boards with excellent sound control; keeps its R-value when wet.
Fiberglass batts
The most common and economical insulation; must be cut and fitted carefully because gaps and compression sharply reduce real-world performance.
Fiberglass blown-in
Loose-fill for open attic floors; fast to install and settles into an even blanket over large horizontal areas.
EPS rigid board
Expanded polystyrene; the most affordable rigid foam, used for continuous exterior and below-grade insulation.
XPS rigid board
Extruded polystyrene; moisture-resistant rigid board common under slabs and on foundation walls.
Closed-cell spray foam
The highest R-value of any common insulation; also acts as an air and vapor barrier and adds structural rigidity. Ideal for rim joists, basements, crawlspaces and unvented roof decks.
Polyiso rigid board
The highest-R rigid foam board; foil-faced and used for continuous exterior insulation to stop thermal bridging.
Cellulose (dense-pack)
Recycled paper fiber treated for fire and pests; dense-packs into closed wall cavities, making it ideal for retrofits.
Wood fiber
Renewable, carbon-storing batts and boards with strong sound dampening and vapor-open performance.
Common Spray Foam Applications in Burlington
Crawlspaces
Encapsulating a crawlspace with foam stops ground moisture and cold floors above.
Attics & roof decks
The top source of heat loss; foam on the roof deck creates a conditioned, sealed attic.
Exterior walls
Foam fills stud cavities completely, eliminating the gaps that reduce batt performance.
Rim & band joists
A major air-leak point where the foundation meets framing; closed-cell foam seals and insulates it.
Why Burlington Homes Need the Right Insulation
Burlington is located in Burlington, in IECC Climate Zone 5A. Its housing includes a mix of colonials, capes, ranches, and newer construction, which means improving comfort and cutting energy bills through better insulation and air sealing is a priority for local property owners. The right insulation strategy depends on the age and construction of each home.
Choosing an Insulation Contractor in Burlington
Spray foam involves chemical reactions and strict safety steps, so the installer matters. In Burlington, look for a contractor who:
- Follows OSHA safety practices with proper ventilation and respirators during spraying
- Holds industry credentials such as SPFA (Spray Polyurethane Foam Alliance) training
- Documents R-values and provides what you need for code sign-off
- Manufacturer-certified to install specific foam systems and keep warranties valid
- Provides a clear written scope and estimate before starting
- Carries general liability and workers’ compensation coverage
- Licensed and fully insured for insulation work in Massachusetts
- Uses the correct foam type and thickness for each assembly to avoid off-ratio foam
Massachusetts Insulation R-Value Requirements
Burlington falls in IECC Climate Zone 5A. New and renovated homes must meet these minimum insulation levels under the Massachusetts energy code.
| Assembly | Minimum R-value (Zone 5) |
|---|---|
| Wood-frame walls | R-20, or R-13 cavity + R-5 continuous |
| Ceilings / attics | R-49 to R-60 |
| Floors over unconditioned space | R-30 |
| Basement walls | R-15 continuous or R-19 cavity |
| Crawlspace walls | R-15 continuous or R-19 cavity |
| Slab edge (heated) | R-10, 2 ft deep |
Reaching Stretch-Code R-Values with a Hybrid System
A hybrid assembly lets you buy performance only where it counts. A shallow layer of closed-cell handles air-sealing and moisture control on the cold face, while a cheaper fill carries the bulk of the thermal resistance in the rest of the cavity.
The Flash — Closed-Cell
That initial closed-cell pass — placed tight to the sheathing — provides the air barrier and the vapor control the assembly needs, and at about R-6.5 per inch a two-inch layer adds roughly R-13.
The Fill
Whatever depth remains gets finished with an affordable fill — open-cell, cellulose, or batt insulation — to top off the total.
Worked Example — R-30 Wall
A common recipe for a Zone 5 R-30 wall in a 2×6 cavity: about 2 inches of closed-cell (≈ R-13) against the sheathing, then roughly 4.5–5 inches of open-cell or dense-pack (≈ R-16–18), for a combined R-29 to R-31.
Because the warm, vapor-tight foam sits on the exterior side, the sheathing never gets cold enough for condensation to form. The one requirement is a closed-cell layer thick enough for Massachusetts' Zone 5 conditions.
Frequently Asked Questions
What is the difference between open-cell and closed-cell foam?
Closed-cell foam is denser, delivers about R-6 to R-7 per inch, and acts as an air and vapor barrier — good for rim joists, basements, and roof decks. Open-cell is lighter, about R-3.5 to R-3.8 per inch, vapor-permeable, and often used in walls and attics.
Is spray foam insulation worth it for a Burlington home?
For most Burlington homes it is. Spray foam insulates and air-seals at once, which usually cuts heating and cooling costs more than batts alone and helps older homes feel far more comfortable.
What R-value do you get from 2 inches of closed-cell spray foam?
At roughly R-6.5 to R-7 per inch, two inches of closed-cell foam delivers about R-13 — and just as importantly, that layer also air-seals the cavity and provides vapor control. On many Burlington walls we pair that 2-inch flash with a lower-cost fill to reach the full R-value target economically.
Do I need to insulate to meet the Massachusetts energy code?
Yes. Massachusetts follows the IECC (Climate Zone 5) with the state Stretch Code, which sets minimum R-values for walls, ceilings, floors, and foundations. We make sure your Burlington project documents and meets those levels.
Will new insulation help with drafts and high energy bills?
Almost always. Most wasted energy in Burlington homes comes from air leaks, not just missing insulation. Air sealing plus the right insulation is the most reliable way to fix drafts, cold rooms, and high bills.
Can insulation be added to an existing Burlington home?
Yes. Dense-pack cellulose, injection foam, and spray foam can all be added to existing homes — often without major demolition — to improve comfort and efficiency.
What R-value is required for spray foam in Massachusetts?
Massachusetts sits in Climate Zone 5. Above-grade walls generally need about R-20 (or R-13 cavity plus R-5 continuous), attics roughly R-49 to R-60, floors over unconditioned space about R-30, and basement or crawlspace walls around R-15 continuous. We size the foam on every Burlington project to the value your assembly needs to pass code.
How do you reach R-30 in a wall with spray foam?
The most cost-effective route is a flash-and-fill assembly: about 2 inches of closed-cell foam (≈ R-13) against the sheathing, then the rest of the cavity filled with open-cell, dense-pack cellulose, or batt (≈ R-16 to R-18). In a standard Burlington 2x6 wall that combination lands right around R-30.
Does Mass Save cover spray foam insulation?
Mass Save is a real Massachusetts efficiency program that Burlington homeowners can explore. It typically funds a no-cost home energy assessment and offers incentives toward weatherization and air sealing; coverage for spray foam specifically can vary and often depends on the assessment, so we help you understand what your project may qualify for.
