Spray Foam Insulation Beverly MA - Quick Facts
Local energy code in Beverly
- As of January 1, 2026, Beverly enforces the Massachusetts Specialized (Opt-In) Energy Code on top of the Stretch Code baseline - IECC Climate Zone 5A.
- The Opt-In code goes further than the Stretch baseline: new fossil-fuel homes must be pre-wired for electrification and include on-site solar where roof space allows.
- New all-electric homes rely on heat pumps for heat and hot water; large fossil-fuel homes over 4,000 sq ft must hit net-zero (HERS 0), and multifamily over 12,000 sq ft must be Passive House.
Insulation & air sealing in Beverly
- Spray foam is one of the fastest ways to hit the 3.0 ACH50 blower door target and the HERS 42/45 scores required in Beverly.
- Envelope R-values follow IECC Climate Zone 5A (roughly R-49 to R-60 attic and R-20+ walls).
- Open-cell and closed-cell assemblies are evaluated during HERS plan review; as RESNET raters, not an insulation contractor, we give unbiased guidance on where R-value and air-sealing dollars move your score most.
Mass Save rebates for Beverly (2026)
- Better air sealing and insulation move projects into higher Mass Save tiers - up to $25,000 for a new all-electric single-family home and up to $30,000 (Level 2) for all-electric renovations - verified by a RESNET-certified HERS rater.
RESNET-certified · 15,000+ ratings completed · 5.0 stars across 136 Google reviews · (617) 501-6788
Spray Foam Insulation Installer in Beverly, MA
Insulation is one of the highest-return upgrades a Beverly property owner can make. We install spray foam and insulation, help you choose the right foam for each assembly, and handle Massachusetts energy-code compliance.
We Install Spray Foam in Beverly
Home Energy Efficiency Consultants installs spray foam insulation for Beverly homeowners, builders and contractors. We are also certified HERS raters, so the same company that installs your foam can run the blower door test and the HERS rating your permit may need.
- Where we install it: attics and roof lines, rim joists, exterior walls, kneewalls, basements and crawl spaces.
- How a job runs: we look at the house, give you a written scope and price, install the foam, then test the results.
- Why one team helps: the people who sealed the house are the people who test it, so air leaks found on the blower door test get fixed before the final rating.
Our Everett office at 371 Main St, Everett serves Beverly. Request a spray foam quote or call 617-501-6788.
Which Spray Foam Is Right for Your Project?
Spray foam comes in two families, and the right choice shapes both performance and cost on a Beverly project.
Closed-Cell Spray Foam
Dense and rigid at roughly R-6 to R-7 per inch — the highest R-value of common insulation. It also acts as an air and vapor barrier and adds stiffness, making it ideal for rim joists, basements, crawlspaces, and roof decks in Beverly homes.
Open-Cell Spray Foam
Lighter and vapor-permeable at about R-3.5 to R-3.8 per inch. It expands to fill irregular cavities, seals air leaks, and dampens sound — a strong choice for interior walls and attics where drying potential matters.
Insulation Types & R-Values Per Inch
R-value measures resistance to heat flow — higher is better. Here is how the insulation materials used on Beverly, Beverly projects compare per inch of thickness.
Mineral wool (rock wool)
Dense, naturally fire-resistant and water-repellent batts or boards with excellent sound control; keeps its R-value when wet.
XPS rigid board
Extruded polystyrene; moisture-resistant rigid board common under slabs and on foundation walls.
Fiberglass batts
The most common and economical insulation; must be cut and fitted carefully because gaps and compression sharply reduce real-world performance.
EPS rigid board
Expanded polystyrene; the most affordable rigid foam, used for continuous exterior and below-grade insulation.
Cellulose (dense-pack)
Recycled paper fiber treated for fire and pests; dense-packs into closed wall cavities, making it ideal for retrofits.
Open-cell spray foam
Lighter and vapor-permeable; expands fully to fill irregular cavities, seals air leaks and dampens sound. A common choice for interior walls and vented attics.
Wood fiber
Renewable, carbon-storing batts and boards with strong sound dampening and vapor-open performance.
Closed-cell spray foam
The highest R-value of any common insulation; also acts as an air and vapor barrier and adds structural rigidity. Ideal for rim joists, basements, crawlspaces and unvented roof decks.
Fiberglass blown-in
Loose-fill for open attic floors; fast to install and settles into an even blanket over large horizontal areas.
Polyiso rigid board
The highest-R rigid foam board; foil-faced and used for continuous exterior insulation to stop thermal bridging.
Best Places to Use Spray Foam in Beverly
Rim & band joists
A major air-leak point where the foundation meets framing; closed-cell foam seals and insulates it.
Attics & roof decks
The top source of heat loss; foam on the roof deck creates a conditioned, sealed attic.
Cathedral ceilings
Foam insulates tight roof-line assemblies where batts cannot breathe or fit well.
Basement & foundation walls
Closed-cell foam controls moisture and adds R-value below grade.
Exterior walls
Foam fills stud cavities completely, eliminating the gaps that reduce batt performance.
Massachusetts Insulation R-Value Requirements
Beverly falls in IECC Climate Zone 5A. New and renovated homes must meet these minimum insulation levels under the Massachusetts energy code.
| Assembly | Minimum R-value (Zone 5) |
|---|---|
| Wood-frame walls | R-20, or R-13 cavity + R-5 continuous |
| Ceilings / attics | R-49 to R-60 |
| Floors over unconditioned space | R-30 |
| Basement walls | R-15 continuous or R-19 cavity |
| Crawlspace walls | R-15 continuous or R-19 cavity |
| Slab edge (heated) | R-10, 2 ft deep |
Choosing an Insulation Contractor in Beverly
Spray foam involves chemical reactions and strict safety steps, so the installer matters. In Beverly, look for a contractor who:
- Licensed and fully insured for insulation work in Massachusetts
- Uses the correct foam type and thickness for each assembly to avoid off-ratio foam
- Provides a clear written scope and estimate before starting
- Follows OSHA safety practices with proper ventilation and respirators during spraying
- Carries general liability and workers’ compensation coverage
- Knows Massachusetts code, including ignition and thermal barrier requirements
- Manufacturer-certified to install specific foam systems and keep warranties valid
- Holds industry credentials such as SPFA (Spray Polyurethane Foam Alliance) training
Serving Beverly and the Surrounding Area
Because Beverly sits in Beverly and IECC Climate Zone 5A, insulation and air sealing carry a real payback. We match materials and methods to a mix of colonials, capes, ranches, and newer construction so the work lasts and performs.
Combining Closed-Cell and Fill Insulation
A hybrid assembly lets you buy performance only where it counts. A shallow layer of closed-cell handles air-sealing and moisture control on the cold face, while a cheaper fill carries the bulk of the thermal resistance in the rest of the cavity.
The Flash — Closed-Cell
That initial closed-cell pass — placed tight to the sheathing — provides the air barrier and the vapor control the assembly needs, and at about R-6.5 per inch a two-inch layer adds roughly R-13.
The Fill
The remaining cavity is filled with a budget-friendly material such as open-cell foam or dense-pack cellulose to complete the R-value.
Worked Example — R-30 Wall
For an R-30 target in a standard 5.5-inch bay: pair a 2-inch closed-cell flash (≈ R-13) with about 4.5 inches of open-cell or cellulose (≈ R-17), landing right around R-30.
Keeping the impermeable closed-cell on the cold, outer face keeps the sheathing above the dew point, so moisture can't condense inside the wall — the key rule is making that foam layer thick enough for our Zone 5 climate.
Insulating Homes in Beverly
Beverly's 2016 Housing Production Plan found that 41% of homes were built before World War II and 82% before 1980. Single-family detached homes are the largest group at about 53%, with two- to four-unit buildings making up about 19%.
Older single-family homes in Beverly usually need the attic and rim joist sealed first. Capes and older colonials with finished upstairs rooms benefit from spray foam on kneewalls and roof slopes. Coastal homes see more wind, so air sealing pays off. Wiring and moisture are checked before any walls are filled.
- The Municipal Inspections/Building Department at 8 Dane Street issues permits for new structures, additions, alterations and repairs. The department notes that permit applications must include an energy code checklist.
- Beverly has adopted the Specialized (Opt-In) Code (effective 1/1/2026), which builds on the Stretch Code it has followed since 2012. New homes here face extra requirements, and the Stretch Code targets still frame the work: HERS 42 for mixed-fuel or 45 for all-electric new homes, and HERS 65 / 70 for renovations and additions over 1,000 sq ft or over 100% of the existing home. On smaller jobs, the rule to remember is 225 CMR 22 R503.1.1: exposed wall cavities in an alteration must be filled with insulation of at least R-3.7 per inch.
What spray foam can do for a Beverly home
- Beverly capes and older colonials with finished upstairs rooms benefit from foam on kneewalls and roof slopes, which warms bedrooms and limits ice dams.
- Sealing the attic and rim joist of an older Beverly single-family home is the first step toward fewer drafts and steadier room temperatures.
- Coastal Beverly homes see more wind, and a tight spray foam seal keeps gusts from driving cold air and outdoor pollen through every gap.
Our Everett office at 371 Main St serves Beverly. After the insulation is in, HEEC can follow up with a blower door test to measure how much air leakage was cut, and a HERS rating if your project needs one for the energy code.
Spray Foam Facts for Beverly Homeowners
How much energy can spray foam save in Beverly?
ENERGY STAR estimates homeowners save an average of 15% on heating and cooling costs, or about 11% on total energy costs, by air sealing and adding insulation in attics, floors over crawl spaces and basements. Spray foam does both jobs at once. Actual savings in Beverly depend on how leaky the house is to start, which is why we measure it with a blower door test before and after the work.
How do open-cell and closed-cell foam compare for Beverly houses?
Open-cell foam is light and vapor-permeable, at roughly R-3.6 per inch, and works well in above-grade walls and rooflines. Closed-cell foam is dense, at roughly R-6 per inch, and acts as a vapor retarder, so it is the better choice for rim joists, basement walls and anywhere moisture is a concern. The U.S. Department of Energy notes open-cell foam should not be used below ground level, and its Building America guide recommends at least 1.5 inches of closed-cell foam in cold-climate hybrid walls. Many Beverly jobs use both.
Is the house off-limits during a spray foam job in Beverly?
Yes, plan to be out. The EPA advises occupants to vacate during spray foam application and to wait until the foam has cured and the space has been ventilated and cleaned. Some manufacturers recommend about 24 hours before re-entry for professional two-component systems; we follow the specific product's guidance and tell you the exact timing before the job.
Which energy code applies to renovations in Beverly?
Beverly follows the Specialized (Opt-In) Code (effective 1/1/2026). For additions, gut renovations and new homes that means meeting stricter insulation and air-leakage targets, often verified with a blower door test or a HERS rating. Our Everett (371 Main St) office handles Beverly jobs and can test the house with a blower door before and after the foam goes in.
Can Beverly homeowners get help paying for insulation?
Mass Save offers 75–100% off approved insulation and air sealing improvements for 1- to 4-unit homes, plus 0% HEAT Loan financing of up to $25,000 for qualifying upgrades. Whether a specific spray foam measure qualifies depends on the program rules, so confirm before you start. The federal Energy Efficient Home Improvement Credit (25C) only covered property placed in service through 2025, so it no longer applies to new work.
Sources: U.S. Department of Energy (Building America Spray Foam Guide; Energy Saver), ENERGY STAR, Mass Save, IRS, U.S. EPA.
Spray Foam Types, R-Values and Vapor Control for Beverly Homes
| Open-cell (about 0.5 lb density) | Closed-cell (about 2 lb density) | |
|---|---|---|
| R-value | About R-3.6 per inch | About R-6 per inch |
| Air barrier | Yes | Yes |
| Moisture vapor | Vapor-permeable (about 5–10 perms at 5 in.) | Class II vapor retarder (under 1 perm at 2 in.) |
| Below grade / basements | Not recommended | Yes |
| Adds wall strength | No | Yes, increases racking strength |
| Typical uses | Above-grade walls, rooflines, sound control | Foundation walls, rim joists, sills, cold-climate walls |
| Cost | Lower | Higher |
Does closed-cell spray foam stop moisture vapor?
At about 2 inches thick, closed-cell foam is rated under 1 perm, which makes it a Class II vapor retarder under the residential building code (0.1 to 1.0 perm). That is not quite a Class I "vapor barrier" like polyethylene sheeting (0.1 perm or less), but it is low enough that most Beverly walls don't need a separate plastic layer. Open-cell foam is vapor-permeable, at roughly 5 to 10 perms at 5 inches, so it may need a separate vapor retarder depending on the wall design.
What R-value does spray foam give in a 2x4 or 2x6 wall?
Using DOE's typical values of about R-3.6 per inch for open-cell and R-6 per inch for closed-cell: a full 3.5-inch 2x4 cavity is about R-13 with open-cell or about R-21 with closed-cell, and a 5.5-inch 2x6 cavity is about R-20 with open-cell. Closed-cell is often sprayed 2 to 3 inches deep (about R-12 to R-18) and paired with another insulation. Because foam also seals air leaks, it usually performs better than its R-value alone suggests.
Do I need drywall over spray foam?
In most cases, yes. The residential building code (IRC R316.4) requires foam plastic to be separated from living space by a thermal barrier of at least 1/2-inch drywall or an approved equivalent. In attics and crawl spaces entered only for service, an ignition barrier such as 1/4-inch plywood, 3/8-inch drywall or 1.5 inches of mineral fiber may be used instead, unless the specific foam product is approved to be left exposed. We confirm which applies before the job.
How does spray foam affect ice dams?
Ice dams form when heat escaping from the house warms the roof deck, melting snow that refreezes at the colder eaves. Massachusetts and DOE guidance both put air sealing the attic first, followed by insulation. Spray foam does both: on the attic floor it stops warm air from reaching the roof, and sprayed under the roof deck it creates an unvented, conditioned attic. It works best with a blower door test to find the leaks first.
Does spray foam add strength to framing?
Closed-cell foam is rigid once cured, and the Department of Energy's Building America guide reports that it substantially increases the racking strength of frame walls when used in the stud cavities. Open-cell foam is soft and flexible and does not add meaningful strength.
Is spray foam a good fit for a Beverly basement or foundation?
Yes, with closed-cell foam. Department of Energy guidance calls for closed-cell spray foam on the inside of the foundation wall and along the sill. Open-cell foam should not be used below ground level because it can absorb water. Any water leaks or moisture problems in the basement have to be fixed first, and in finished or living space the foam must be covered with a code-approved thermal barrier such as 1/2-inch drywall.
Sources: U.S. DOE Building America Spray Foam Guide and Building America Solution Center; DOE Energy Saver; International Residential Code R316 and vapor retarder classes; Mass.gov ice dam guidance.
Existing Walls, Moisture and Crawl Spaces in Beverly
What is the best way to insulate a crawl space in Beverly?
DOE's Building America guidance favors an unvented, insulated crawl space: insulate the perimeter walls instead of the floor above, cover the ground with sealed 6-mil polyethylene, and provide a drying method such as a small exhaust fan or conditioned air supply (at least 1 CFM per 50 square feet of floor area, or 50 CFM). Closed-cell spray foam is a common way to insulate and air-seal those walls and the rim joist. Check with the Beverly building department on radon, pest and fire-barrier requirements before you start.
Can I spray foam my Beverly home myself?
Small jobs are possible, but the EPA cautions that do-it-yourself applicators are often unaware of the inhalation and skin hazards. EPA describes three product types: one-component foam in cans for small gaps, low-pressure two-component kits for small areas, and high-pressure professional systems that require supplied-air respirators and protective clothing. Whole-wall, attic and basement jobs call for the professional system, and occupants should stay out until the foam has cured and the space is ventilated.
Does spray foam reduce outside noise in Beverly?
It helps with sound that leaks through gaps, because foam seals the cracks and openings that let airborne noise in. Open-cell foam is softer and absorbs more sound than closed-cell. It is not a full soundproofing system on its own - walls facing heavy traffic usually also need added mass, such as an extra layer of drywall, for a big reduction.
Can spray foam be added to the finished walls of a Beverly home?
Often, yes - but usually not with the same spray foam used on open framing. The Department of Energy lists foamed-in-place insulation and blown-in loose fill such as dense-pack cellulose as options for enclosed existing walls; both go in through small holes that are patched afterward. Standard two-part spray foam is sprayed into open cavities, so it fits best when walls are already open during a remodel, or at rim joists, attics and basements you can reach. What is already in the wall, and whether it has had moisture problems, decides which method is right.
Will spray foam cause moisture or mold problems in my Beverly home?
Not when the assembly is designed for our cold climate. Foam does not fix liquid water, so roof, plumbing and foundation leaks have to be repaired first. Closed-cell foam slows vapor and, at the right thickness, keeps the inside face of the sheathing warm; DOE's Building America guide calls for at least 1.5 inches of closed-cell in cold-climate hybrid walls for that reason. Open-cell foam lets vapor pass, so the wall needs a drying path or a separate vapor retarder depending on the design.
Sources: U.S. DOE Energy Saver (insulation types); DOE Building America Spray Foam Guide and Solution Center (unvented crawlspaces); U.S. EPA (spray polyurethane foam product types).
Frequently Asked Questions
Does Mass Save cover spray foam insulation?
Mass Save is a genuine Massachusetts efficiency program, and for Beverly homeowners it's worth exploring. It typically funds a no-cost home energy assessment and offers strong incentives toward weatherization and air sealing; coverage for spray foam specifically can vary and often depends on the assessment and the insulation type, so we help you understand what your project may qualify for rather than promising a fixed rebate.
Can insulation be added to an existing Beverly home?
Yes. Dense-pack cellulose, injection foam, and spray foam can all be added to existing homes — often without major demolition — to improve comfort and efficiency.
Why do some people remove or worry about spray foam insulation?
Most concerns trace back to foam that was installed at the wrong thickness, in the wrong mix ratio, or without proper ventilation — which can lead to odor or poor curing. Correctly installed foam from a certified crew performs reliably for decades. On every Beverly job we verify substrate conditions, mix ratios, and thickness, and document the R-values so the assembly is done right the first time.
Is spray foam safe once it is installed?
Once cured, spray foam is inert and safe. A qualified installer follows manufacturer cure times, ventilation, and — where code requires — an ignition or thermal barrier over the foam.
What is the difference between open-cell and closed-cell foam?
Closed-cell foam is denser, delivers about R-6 to R-7 per inch, and acts as an air and vapor barrier — good for rim joists, basements, and roof decks. Open-cell is lighter, about R-3.5 to R-3.8 per inch, vapor-permeable, and often used in walls and attics.
How much insulation does an attic need?
Massachusetts code targets about R-49 to R-60 in attics. Because attics are usually the biggest source of heat loss, they are often the most cost-effective place to add insulation first.
What R-value is required for spray foam in Massachusetts?
Massachusetts sits in Climate Zone 5. Above-grade walls generally need about R-20 (or R-13 cavity plus R-5 continuous), attics roughly R-49 to R-60, floors over unconditioned space about R-30, and basement or crawlspace walls around R-15 continuous. We size the foam on every Beverly project to the value your assembly needs to pass code.
What R-value do you get from 2 inches of closed-cell spray foam?
At about R-6.5 to R-7 per inch, two inches of closed-cell foam gives roughly R-13, and that layer also air-seals the cavity and controls vapor. On many Beverly walls we pair a 2-inch closed-cell flash with a lower-cost fill to reach the full target economically.
How do you reach R-30 in a wall with spray foam?
The most cost-effective route is a flash-and-fill assembly: about 2 inches of closed-cell foam (≈ R-13) against the sheathing, then the rest of the cavity filled with open-cell, dense-pack cellulose, or batt (≈ R-16 to R-18). In a standard Beverly 2x6 wall that combination lands right around R-30.
Is Beverly under the Specialized (Opt-In) Code?
Yes. According to the state's adoption list, Beverly adopted the Specialized (Opt-In) Code effective January 1, 2026.
Do Beverly building permits involve the energy code?
Yes. Beverly's Building Department says permit applications must include an energy code checklist.
Mass Save®-Listed HERS Rater
U.S. DOE Efficient New HomeTrusted Partner — Verified
ENERGY STAR®Partner
Phius CertifiedPassive House Verifier
ICCMember★★★★★136 Google
Reviews
The Phius Certified Verifier logo is used under license from Phius.
HERS Ratings Across Beverly and Nearby Communities
Home Energy Efficiency Consultants rates new homes, additions, and major renovations throughout Beverly — from Beverly Farms, Prides Crossing, and Ryal Side to Montserrat and North Beverly. Every Beverly project is filed with the City of Beverly Building Department, and we handle the energy model, blower door and duct leakage testing, and the compliance paperwork from start to finish.
We also serve the communities right around Beverly, including Salem, Danvers, Peabody, Wenham, and Hamilton. Our Everett office at 371 Main St is the closest of our four Massachusetts locations — see our Everett office or call (617) 501-6788 to get a Beverly rating on the schedule.
Beverly Specialized Energy Code — HERS Index Targets
Beverly enforces the Massachusetts Specialized (Opt-In) Energy Code. The required HERS score depends on fuel type and project scope — a lower index is stricter.
| Project type | Mixed-fuel | Mixed-fuel + solar | All-electric | All-electric + solar |
|---|---|---|---|---|
| New construction | HERS 42 | 42 | 45 | 45 |
| New construction — embodied-carbon credit | 45 | 45 | 48 | 48 |
| Accessory dwelling unit (ADU) | 52 | 55 | 55 | 58 |
| Major alteration / renovation / change of use | 65 | 70 | 70 | 75 |
A HERS rating is triggered by new construction, additions over 1,000 sq ft (or more than 100% of the existing conditioned area), and Level 3 alterations over 1,000 sq ft affecting more than 50% of the home. New homes must also pass a blower-door test at 3.0 ACH50 and include electrification-ready wiring for heat pumps, EV charging, and solar. We model your Beverly project up front so you know the exact target and the fastest path to hit it — call (617) 501-6788.
