Spray Foam Insulation Hull MA - Quick Facts
Local energy code in Hull
- Hull is a Stretch Code community - the statewide baseline for new construction and major renovations. IECC Climate Zone 5A.
- Massachusetts has three energy-code levels - base (2021 IECC), Stretch, and Specialized (Opt-In) - and Hull is on the Stretch Code.
Insulation & air sealing in Hull
- Spray foam is one of the fastest ways to hit the 3.0 ACH50 blower door target and the HERS 42/45 scores required in Hull.
- Envelope R-values follow IECC Climate Zone 5A (roughly R-49 to R-60 attic and R-20+ walls).
- Open-cell and closed-cell assemblies are evaluated during HERS plan review; as RESNET raters, not an insulation contractor, we give unbiased guidance on where R-value and air-sealing dollars move your score most.
Mass Save rebates for Hull (2026)
- Better air sealing and insulation move projects into higher Mass Save tiers - up to $25,000 for a new all-electric single-family home and up to $30,000 (Level 2) for all-electric renovations - verified by a RESNET-certified HERS rater.
RESNET-certified · 15,000+ ratings completed · 5.0 stars across 136 Google reviews · (617) 501-6788
Spray Foam Insulation Installer in Hull, MA
In Massachusetts, improving comfort and cutting energy bills through better insulation and air sealing matters year-round. Our team installs spray foam and helps Hull homeowners choose the insulation that fits their home and meets code.
We Install Spray Foam in Hull
Home Energy Efficiency Consultants installs spray foam insulation for Hull homeowners, builders and contractors. We are also certified HERS raters, so the same company that installs your foam can run the blower door test and the HERS rating your permit may need.
- Where we install it: attics and roof lines, rim joists, exterior walls, kneewalls, basements and crawl spaces.
- How a job runs: we look at the house, give you a written scope and price, install the foam, then test the results.
- Why one team helps: the people who sealed the house are the people who test it, so air leaks found on the blower door test get fixed before the final rating.
Our Somerville office at 519 Broadway, Somerville serves Hull. Request a spray foam quote or call 617-501-6788.
Two Types of Spray Foam, Two Jobs
Spray foam comes in two families, and the right choice shapes both performance and cost on a Hull project.
Closed-Cell Spray Foam
Dense and rigid at roughly R-6 to R-7 per inch — the highest R-value of common insulation. It also acts as an air and vapor barrier and adds stiffness, making it ideal for rim joists, basements, crawlspaces, and roof decks in Hull homes.
Open-Cell Spray Foam
Lighter and vapor-permeable at about R-3.5 to R-3.8 per inch. It expands to fill irregular cavities, seals air leaks, and dampens sound — a strong choice for interior walls and attics where drying potential matters.
Insulation Types & R-Values Per Inch
R-value measures resistance to heat flow — higher is better. Here is how the insulation materials used on Hull, Hull projects compare per inch of thickness.
Cellulose (dense-pack)
Recycled paper fiber treated for fire and pests; dense-packs into closed wall cavities, making it ideal for retrofits.
Fiberglass batts
The most common and economical insulation; must be cut and fitted carefully because gaps and compression sharply reduce real-world performance.
Fiberglass blown-in
Loose-fill for open attic floors; fast to install and settles into an even blanket over large horizontal areas.
Mineral wool (rock wool)
Dense, naturally fire-resistant and water-repellent batts or boards with excellent sound control; keeps its R-value when wet.
Closed-cell spray foam
The highest R-value of any common insulation; also acts as an air and vapor barrier and adds structural rigidity. Ideal for rim joists, basements, crawlspaces and unvented roof decks.
Polyiso rigid board
The highest-R rigid foam board; foil-faced and used for continuous exterior insulation to stop thermal bridging.
Open-cell spray foam
Lighter and vapor-permeable; expands fully to fill irregular cavities, seals air leaks and dampens sound. A common choice for interior walls and vented attics.
EPS rigid board
Expanded polystyrene; the most affordable rigid foam, used for continuous exterior and below-grade insulation.
XPS rigid board
Extruded polystyrene; moisture-resistant rigid board common under slabs and on foundation walls.
Wood fiber
Renewable, carbon-storing batts and boards with strong sound dampening and vapor-open performance.
Meeting the Massachusetts Energy Code
Hull falls in IECC Climate Zone 5A. New and renovated homes must meet these minimum insulation levels under the Massachusetts energy code.
| Assembly | Minimum R-value (Zone 5) |
|---|---|
| Wood-frame walls | R-20, or R-13 cavity + R-5 continuous |
| Ceilings / attics | R-49 to R-60 |
| Floors over unconditioned space | R-30 |
| Basement walls | R-15 continuous or R-19 cavity |
| Crawlspace walls | R-15 continuous or R-19 cavity |
| Slab edge (heated) | R-10, 2 ft deep |
Best Places to Use Spray Foam in Hull
Rim & band joists
A major air-leak point where the foundation meets framing; closed-cell foam seals and insulates it.
Bonus rooms & knee walls
Sealing these awkward areas fixes the hot-and-cold rooms common over garages.
Cathedral ceilings
Foam insulates tight roof-line assemblies where batts cannot breathe or fit well.
Exterior walls
Foam fills stud cavities completely, eliminating the gaps that reduce batt performance.
Attics & roof decks
The top source of heat loss; foam on the roof deck creates a conditioned, sealed attic.
Serving Hull and the Surrounding Area
Homes in Hull (Hull) face IECC Climate Zone 5A winters, so heat loss adds up quickly. With a mix of colonials, capes, ranches, and newer construction, improving comfort and cutting energy bills through better insulation and air sealing is where the biggest energy savings usually come from.
Choosing an Insulation Contractor in Hull
Spray foam involves chemical reactions and strict safety steps, so the installer matters. In Hull, look for a contractor who:
- Licensed and fully insured for insulation work in Massachusetts
- Uses the correct foam type and thickness for each assembly to avoid off-ratio foam
- Provides a clear written scope and estimate before starting
- Knows Massachusetts code, including ignition and thermal barrier requirements
- Follows OSHA safety practices with proper ventilation and respirators during spraying
- Carries general liability and workers’ compensation coverage
- Manufacturer-certified to install specific foam systems and keep warranties valid
Combining Closed-Cell and Fill Insulation
One of the most cost-effective ways to reach a demanding wall R-value is to pair a thin layer of closed-cell foam with a less expensive filler. A first pass of closed-cell is sprayed tight against the sheathing, and the remainder of the cavity is completed with open-cell foam, dense-pack cellulose, or a batt.
The Flash — Closed-Cell
That initial closed-cell pass — placed tight to the sheathing — provides the air barrier and the vapor control the assembly needs, and at about R-6.5 per inch a two-inch layer adds roughly R-13.
The Fill
The remaining cavity is filled with a budget-friendly material such as open-cell foam or dense-pack cellulose to complete the R-value.
Worked Example — R-30 Wall
A typical Massachusetts R-30 build stacks a 2-inch closed-cell layer (≈ R-13) with 4.5–5 inches of open-cell foam or dense-pack cellulose (≈ R-16–18) to total roughly R-30 in one 2×6 cavity.
Because the warm, vapor-tight foam sits on the exterior side, the sheathing never gets cold enough for condensation to form. The one requirement is a closed-cell layer thick enough for Massachusetts' Zone 5 conditions.
Spray Foam Work by Our Crew
Real photos from our spray foam insulation jobs in Massachusetts.
Spray Foam Facts for Hull Homeowners
Which type of spray foam should a Hull homeowner choose?
Open-cell foam is light and vapor-permeable, at roughly R-3.6 per inch, and works well in above-grade walls and rooflines. Closed-cell foam is dense, at roughly R-6 per inch, and acts as a vapor retarder, so it is the better choice for rim joists, basement walls and anywhere moisture is a concern. The U.S. Department of Energy notes open-cell foam should not be used below ground level, and its Building America guide recommends at least 1.5 inches of closed-cell foam in cold-climate hybrid walls. Many Hull jobs use both.
Is the house off-limits during a spray foam job in Hull?
Yes, plan to be out. The EPA advises occupants to vacate during spray foam application and to wait until the foam has cured and the space has been ventilated and cleaned. Some manufacturers recommend about 24 hours before re-entry for professional two-component systems; we follow the specific product's guidance and tell you the exact timing before the job.
What energy code does Hull follow?
Hull follows the base energy code, which still sets minimum insulation and air-leakage requirements for additions, gut renovations and new homes. Our Everett (371 Main St) office handles Hull jobs and can test the house with a blower door before and after the foam goes in.
What energy savings can Hull homeowners expect from spray foam?
ENERGY STAR estimates homeowners save an average of 15% on heating and cooling costs, or about 11% on total energy costs, by air sealing and adding insulation in attics, floors over crawl spaces and basements. Spray foam does both jobs at once. Actual savings in Hull depend on how leaky the house is to start, which is why we measure it with a blower door test before and after the work.
Can Hull homeowners get help paying for insulation?
Mass Save offers 75–100% off approved insulation and air sealing improvements for 1- to 4-unit homes, plus 0% HEAT Loan financing of up to $25,000 for qualifying upgrades. Whether a specific spray foam measure qualifies depends on the program rules, so confirm before you start. The federal Energy Efficient Home Improvement Credit (25C) only covered property placed in service through 2025, so it no longer applies to new work.
Sources: U.S. Department of Energy (Building America Spray Foam Guide; Energy Saver), ENERGY STAR, Mass Save, IRS, U.S. EPA.
Spray Foam Types, R-Values and Vapor Control for Hull Homes
| Open-cell (about 0.5 lb density) | Closed-cell (about 2 lb density) | |
|---|---|---|
| R-value | About R-3.6 per inch | About R-6 per inch |
| Air barrier | Yes | Yes |
| Moisture vapor | Vapor-permeable (about 5–10 perms at 5 in.) | Class II vapor retarder (under 1 perm at 2 in.) |
| Below grade / basements | Not recommended | Yes |
| Adds wall strength | No | Yes, increases racking strength |
| Typical uses | Above-grade walls, rooflines, sound control | Foundation walls, rim joists, sills, cold-climate walls |
| Cost | Lower | Higher |
Do I need drywall over spray foam?
In most cases, yes. The residential building code (IRC R316.4) requires foam plastic to be separated from living space by a thermal barrier of at least 1/2-inch drywall or an approved equivalent. In attics and crawl spaces entered only for service, an ignition barrier such as 1/4-inch plywood, 3/8-inch drywall or 1.5 inches of mineral fiber may be used instead, unless the specific foam product is approved to be left exposed. We confirm which applies before the job.
Can spray foam help prevent ice dams in Hull?
Ice dams form when heat escaping from the house warms the roof deck, melting snow that refreezes at the colder eaves. Massachusetts and DOE guidance both put air sealing the attic first, followed by insulation. Spray foam does both: on the attic floor it stops warm air from reaching the roof, and sprayed under the roof deck it creates an unvented, conditioned attic. It works best with a blower door test to find the leaks first.
Is there a structural benefit to closed-cell foam in Hull homes?
Closed-cell foam is rigid once cured, and the Department of Energy's Building America guide reports that it substantially increases the racking strength of frame walls when used in the stud cavities. Open-cell foam is soft and flexible and does not add meaningful strength.
Can spray foam go on basement and foundation walls in Hull?
Yes, with closed-cell foam. Department of Energy guidance calls for closed-cell spray foam on the inside of the foundation wall and along the sill. Open-cell foam should not be used below ground level because it can absorb water. Any water leaks or moisture problems in the basement have to be fixed first, and in finished or living space the foam must be covered with a code-approved thermal barrier such as 1/2-inch drywall.
Is closed-cell spray foam a vapor barrier?
At about 2 inches thick, closed-cell foam is rated under 1 perm, which makes it a Class II vapor retarder under the residential building code (0.1 to 1.0 perm). That is not quite a Class I "vapor barrier" like polyethylene sheeting (0.1 perm or less), but it is low enough that most Hull walls don't need a separate plastic layer. Open-cell foam is vapor-permeable, at roughly 5 to 10 perms at 5 inches, so it may need a separate vapor retarder depending on the wall design.
What R-value does spray foam give in a 2x4 or 2x6 wall?
Using DOE's typical values of about R-3.6 per inch for open-cell and R-6 per inch for closed-cell: a full 3.5-inch 2x4 cavity is about R-13 with open-cell or about R-21 with closed-cell, and a 5.5-inch 2x6 cavity is about R-20 with open-cell. Closed-cell is often sprayed 2 to 3 inches deep (about R-12 to R-18) and paired with another insulation. Because foam also seals air leaks, it usually performs better than its R-value alone suggests.
Sources: U.S. DOE Building America Spray Foam Guide and Building America Solution Center; DOE Energy Saver; International Residential Code R316 and vapor retarder classes; Mass.gov ice dam guidance.
More Spray Foam Questions from Hull Homeowners
Can I insulate existing walls in Hull without tearing out drywall?
Often, yes - but usually not with the same spray foam used on open framing. The Department of Energy lists foamed-in-place insulation and blown-in loose fill such as dense-pack cellulose as options for enclosed existing walls; both go in through small holes that are patched afterward. Standard two-part spray foam is sprayed into open cavities, so it fits best when walls are already open during a remodel, or at rim joists, attics and basements you can reach. What is already in the wall, and whether it has had moisture problems, decides which method is right.
Is there a mold risk with spray foam?
Not when the assembly is designed for our cold climate. Foam does not fix liquid water, so roof, plumbing and foundation leaks have to be repaired first. Closed-cell foam slows vapor and, at the right thickness, keeps the inside face of the sheathing warm; DOE's Building America guide calls for at least 1.5 inches of closed-cell in cold-climate hybrid walls for that reason. Open-cell foam lets vapor pass, so the wall needs a drying path or a separate vapor retarder depending on the design.
Does spray foam work in a Hull crawl space?
DOE's Building America guidance favors an unvented, insulated crawl space: insulate the perimeter walls instead of the floor above, cover the ground with sealed 6-mil polyethylene, and provide a drying method such as a small exhaust fan or conditioned air supply (at least 1 CFM per 50 square feet of floor area, or 50 CFM). Closed-cell spray foam is a common way to insulate and air-seal those walls and the rim joist. Check with the Hull building department on radon, pest and fire-barrier requirements before you start.
Can I spray foam my Hull home myself?
Small jobs are possible, but the EPA cautions that do-it-yourself applicators are often unaware of the inhalation and skin hazards. EPA describes three product types: one-component foam in cans for small gaps, low-pressure two-component kits for small areas, and high-pressure professional systems that require supplied-air respirators and protective clothing. Whole-wall, attic and basement jobs call for the professional system, and occupants should stay out until the foam has cured and the space is ventilated.
Will spray foam make my Hull home quieter?
It helps with sound that leaks through gaps, because foam seals the cracks and openings that let airborne noise in. Open-cell foam is softer and absorbs more sound than closed-cell. It is not a full soundproofing system on its own - walls facing heavy traffic usually also need added mass, such as an extra layer of drywall, for a big reduction.
Sources: U.S. DOE Energy Saver (insulation types); DOE Building America Spray Foam Guide and Solution Center (unvented crawlspaces); U.S. EPA (spray polyurethane foam product types).
Insulating Homes in Hull
Hull grew fast as a beach resort. The state's survey says the town went from 72 houses in 1870 to 501 by 1884, with summer cottages of one and a half stories with gabled fronts and side-hall plans, and simple cottages filling the flats along Nantasket Beach. Between 1915 and 1940, many summer homes were converted to year-round use. The town's housing plan says about 67% of homes are single-family.
What to look at first in a Hull home
- Converted summer cottages often have open floors, shallow roofs and little insulation; closed-cell foam handles all three.
- Side-hall cottages have tight half-story rooms with kneewalls, a classic foam job.
- Salt air, flood-prone crawlspaces and old wiring need careful checking first.
Before the work starts
Hull's Building Department at Town Hall, 253 Atlantic Avenue, issues permits for construction, alteration and repair, and asks for site plans with additions and vertical expansions.
Hull is served by the Hull Municipal Lighting Plant. Its 2026 rebates cover air sealing with a blower door test, insulation and duct sealing at 50% of cost up to $750 each, with licensed contractors and a post-install inspection. Mass Save electric offers may not apply to HMLP customers. The state's 2026 Municipal Light Plant Z-Loan (0% interest, up to $25,000) was created for municipal light plant customers who can't use Mass Save financing.
Hull has not adopted the Stretch Code and follows the state's base energy code, so the Stretch Code HERS targets don't apply here. If walls are opened during a remodel, 225 CMR 22 R503.1.1 says those exposed cavities must be filled with insulation rated at least R-3.7 per inch.
Hull jobs are handled from our Somerville office at 519 Broadway. When the work is done, HEEC can follow up with a blower door test and, if your project needs it for the energy code, a HERS rating.
Frequently Asked Questions
What R-value is required for spray foam in Massachusetts?
Massachusetts follows Climate Zone 5 requirements. Above-grade walls generally need about R-20 (or R-13 cavity plus R-5 continuous), attics and ceilings call for roughly R-49 to R-60, floors over unconditioned space about R-30, and basement or crawlspace walls around R-15 continuous. We size the foam on every Hull project to hit the value your assembly needs to pass code.
What is the difference between open-cell and closed-cell foam?
Closed-cell foam is denser, delivers about R-6 to R-7 per inch, and acts as an air and vapor barrier — good for rim joists, basements, and roof decks. Open-cell is lighter, about R-3.5 to R-3.8 per inch, vapor-permeable, and often used in walls and attics.
Is spray foam insulation worth it for a Hull home?
For most Hull homes it is. Spray foam insulates and air-seals at once, which usually cuts heating and cooling costs more than batts alone and helps older homes feel far more comfortable.
Will new insulation help with drafts and high energy bills?
Almost always. Most wasted energy in Hull homes comes from air leaks, not just missing insulation. Air sealing plus the right insulation is the most reliable way to fix drafts, cold rooms, and high bills.
How do you reach R-30 in a wall with spray foam?
The most cost-effective route is a hybrid, or flash-and-fill, assembly: about 2 inches of closed-cell foam (≈ R-13) against the sheathing for the air seal and vapor control, then the rest of the cavity filled with open-cell foam, dense-pack cellulose, or batt (≈ R-16 to R-18). In a standard Hull 2x6 wall that combination lands right around R-30.
Why do some people remove or worry about spray foam insulation?
Most concerns trace back to foam that was installed at the wrong thickness, in the wrong mix ratio, or without proper ventilation — which can lead to odor or poor curing. Correctly installed foam from a certified crew performs reliably for decades. On every Hull job we verify substrate conditions, mix ratios, and thickness, and document the R-values so the assembly is done right the first time.
Has Hull adopted the Stretch Code?
No. According to the state's adoption list, Hull follows the base energy code. When walls are opened, 225 CMR 22 R503.1.1 still requires at least R-3.7 per inch of insulation.
What insulation rebates does Hull Municipal Lighting Plant offer?
Hull's 2026 rebates pay 50% of cost, up to $750 each, for air sealing with a blower door test, insulation and duct sealing, done by a licensed contractor and inspected afterward.
What R-value do you get from 2 inches of closed-cell spray foam?
At about R-6.5 to R-7 per inch, two inches of closed-cell foam gives roughly R-13, and that layer also air-seals the cavity and controls vapor. On many Hull walls we pair a 2-inch closed-cell flash with a lower-cost fill to reach the full target economically.
Does Mass Save cover spray foam insulation?
Mass Save is a real Massachusetts efficiency program that Hull homeowners can explore. It typically funds a no-cost home energy assessment and offers incentives toward weatherization and air sealing; coverage for spray foam specifically can vary and often depends on the assessment, so we help you understand what your project may qualify for.
Mass Save®-Listed HERS Rater
U.S. DOE Efficient New HomeTrusted Partner — Verified
ENERGY STAR®Partner
Phius CertifiedPassive House Verifier
ICCMember★★★★★136 Google
Reviews
The Phius Certified Verifier logo is used under license from Phius.
HERS Ratings in Hull, Massachusetts
Home Energy Efficiency Consultants provides Hull with certified HERS ratings, blower door and duct leakage testing, and Massachusetts energy-code compliance for new construction, additions, and major renovations — with same-day preliminary reports.
We rate homes across the Commonwealth from our four offices. Reach the one nearest your Hull project — Somerville, Framingham, Marlborough, or Everett — or call (617) 501-6788 to schedule a Hull rating.
