Spray Foam Insulation Pembroke MA - Quick Facts
Local energy code in Pembroke
- New construction and major renovations in Pembroke follow the Massachusetts Stretch Energy Code. IECC Climate Zone 5A.
- Massachusetts has three energy-code levels - base (2021 IECC), Stretch, and Specialized (Opt-In) - and Pembroke is on the Stretch Code.
Insulation & air sealing in Pembroke
- Spray foam is one of the fastest ways to hit the 3.0 ACH50 blower door target and the HERS 42/45 scores required in Pembroke.
- Envelope R-values follow IECC Climate Zone 5A (roughly R-49 to R-60 attic and R-20+ walls).
- Open-cell and closed-cell assemblies are evaluated during HERS plan review; as RESNET raters, not an insulation contractor, we give unbiased guidance on where R-value and air-sealing dollars move your score most.
What you can get back: 2026 Mass Save
- Better air sealing and insulation move projects into higher Mass Save tiers - up to $25,000 for a new all-electric single-family home and up to $30,000 (Level 2) for all-electric renovations - verified by a RESNET-certified HERS rater.
RESNET-certified · 15,000+ ratings completed · 5.0 stars across 136 Google reviews · (617) 501-6788
Spray Foam Insulation Installer in Pembroke, MA
In Massachusetts, improving comfort and cutting energy bills through better insulation and air sealing matters year-round. Our team installs spray foam and helps Pembroke homeowners choose the insulation that fits their home and meets code.
We Install Spray Foam in Pembroke
Home Energy Efficiency Consultants installs spray foam insulation for Pembroke homeowners, builders and contractors. We are also certified HERS raters, so the same company that installs your foam can run the blower door test and the HERS rating your permit may need.
- Where we install it: attics and roof lines, rim joists, exterior walls, kneewalls, basements and crawl spaces.
- How a job runs: we look at the house, give you a written scope and price, install the foam, then test the results.
- Why one team helps: the people who sealed the house are the people who test it, so air leaks found on the blower door test get fixed before the final rating.
Our Everett office at 371 Main St, Everett serves Pembroke. Request a spray foam quote or call 617-501-6788.
Open-Cell vs. Closed-Cell Spray Foam
Spray foam comes in two families, and the right choice shapes both performance and cost on a Pembroke project.
Closed-Cell Spray Foam
Dense and rigid at roughly R-6 to R-7 per inch — the highest R-value of common insulation. It also acts as an air and vapor barrier and adds stiffness, making it ideal for rim joists, basements, crawlspaces, and roof decks in Pembroke homes.
Open-Cell Spray Foam
Lighter and vapor-permeable at about R-3.5 to R-3.8 per inch. It expands to fill irregular cavities, seals air leaks, and dampens sound — a strong choice for interior walls and attics where drying potential matters.
Insulation Types & R-Values Per Inch
R-value measures resistance to heat flow — higher is better. Here is how the insulation materials used on Pembroke, Pembroke projects compare per inch of thickness.
Wood fiber
Renewable, carbon-storing batts and boards with strong sound dampening and vapor-open performance.
Mineral wool (rock wool)
Dense, naturally fire-resistant and water-repellent batts or boards with excellent sound control; keeps its R-value when wet.
Closed-cell spray foam
The highest R-value of any common insulation; also acts as an air and vapor barrier and adds structural rigidity. Ideal for rim joists, basements, crawlspaces and unvented roof decks.
Cellulose (dense-pack)
Recycled paper fiber treated for fire and pests; dense-packs into closed wall cavities, making it ideal for retrofits.
XPS rigid board
Extruded polystyrene; moisture-resistant rigid board common under slabs and on foundation walls.
Open-cell spray foam
Lighter and vapor-permeable; expands fully to fill irregular cavities, seals air leaks and dampens sound. A common choice for interior walls and vented attics.
Fiberglass blown-in
Loose-fill for open attic floors; fast to install and settles into an even blanket over large horizontal areas.
Fiberglass batts
The most common and economical insulation; must be cut and fitted carefully because gaps and compression sharply reduce real-world performance.
EPS rigid board
Expanded polystyrene; the most affordable rigid foam, used for continuous exterior and below-grade insulation.
Polyiso rigid board
The highest-R rigid foam board; foil-faced and used for continuous exterior insulation to stop thermal bridging.
Massachusetts Insulation R-Value Requirements
Pembroke falls in IECC Climate Zone 5A. New and renovated homes must meet these minimum insulation levels under the Massachusetts energy code.
| Assembly | Minimum R-value (Zone 5) |
|---|---|
| Wood-frame walls | R-20, or R-13 cavity + R-5 continuous |
| Ceilings / attics | R-49 to R-60 |
| Floors over unconditioned space | R-30 |
| Basement walls | R-15 continuous or R-19 cavity |
| Crawlspace walls | R-15 continuous or R-19 cavity |
| Slab edge (heated) | R-10, 2 ft deep |
Why Pembroke Homes Need the Right Insulation
Serving Pembroke and the rest of Pembroke, we tailor every insulation plan to the local building stock — a mix of colonials, capes, ranches, and newer construction — and to the demands of IECC Climate Zone 5A.
Where Spray Foam Works in Pembroke Homes
Cathedral ceilings
Foam insulates tight roof-line assemblies where batts cannot breathe or fit well.
Attics & roof decks
The top source of heat loss; foam on the roof deck creates a conditioned, sealed attic.
Rim & band joists
A major air-leak point where the foundation meets framing; closed-cell foam seals and insulates it.
Crawlspaces
Encapsulating a crawlspace with foam stops ground moisture and cold floors above.
Choosing an Insulation Contractor in Pembroke
Spray foam involves chemical reactions and strict safety steps, so the installer matters. In Pembroke, look for a contractor who:
- Documents R-values and provides what you need for code sign-off
- Carries general liability and workers’ compensation coverage
- Licensed and fully insured for insulation work in Massachusetts
- Manufacturer-certified to install specific foam systems and keep warranties valid
- Provides a clear written scope and estimate before starting
- Uses the correct foam type and thickness for each assembly to avoid off-ratio foam
How a Flash-and-Fill Wall Hits Its R-Value Target
A hybrid assembly lets you buy performance only where it counts. A shallow layer of closed-cell handles air-sealing and moisture control on the cold face, while a cheaper fill carries the bulk of the thermal resistance in the rest of the cavity.
The Flash — Closed-Cell
That initial closed-cell pass — placed tight to the sheathing — provides the air barrier and the vapor control the assembly needs, and at about R-6.5 per inch a two-inch layer adds roughly R-13.
The Fill
Whatever depth remains gets finished with an affordable fill — open-cell, cellulose, or batt insulation — to top off the total.
Worked Example — R-30 Wall
For an R-30 target in a standard 5.5-inch bay: pair a 2-inch closed-cell flash (≈ R-13) with about 4.5 inches of open-cell or cellulose (≈ R-17), landing right around R-30.
Keeping the impermeable closed-cell on the cold, outer face keeps the sheathing above the dew point, so moisture can't condense inside the wall — the key rule is making that foam layer thick enough for our Zone 5 climate.
Spray Foam Work by Our Crew
Real photos from our spray foam insulation jobs in Massachusetts.
Insulating Homes in Pembroke
Pembroke has old houses and old cottages. The Massachusetts Historical Commission describes late-17th-century center-chimney houses, Greek Revival sidehall cottages, and summer cottages around Bryantville, Great Sandy Bottom Pond and Oldham Pond that were converted to year-round homes after World War II.
Converted cottages are often the hardest homes to keep warm. Many sit on shallow foundations or crawl spaces, with framing that was never meant for winter. Center-chimney houses leak at the sills, around the chimney and through the attic.
Pembroke spray foam priorities
- Floors and crawl spaces under pond-side cottages, after checking for moisture.
- Roof slopes and cathedral ceilings with no attic above.
- Sills and rim joists in older houses.
Pembroke's Building and Inspectional Services department lists HERS ratings among the documents that may be needed with a permit application. HEEC can provide them.
Pembroke and the energy code
Under the Stretch Code, which Pembroke has followed since 7/1/2011, a new home needs a HERS score of 42 (mixed-fuel) or 45 (all-electric). Renovations and additions over 1,000 sq ft, or over 100% of the existing home, need HERS 65 / 70. And under 225 CMR 22 R503.1.1, any exposed wall cavity in an alteration must be filled with insulation of at least R-3.7 per inch.
We keep foam clear of chimneys and check old wiring first.
We serve Pembroke from our Everett office at 371 Main St. When the work is done, HEEC can follow up with a blower door test and a HERS rating, so you know the house is tighter and have the paperwork the code requires.
Spray Foam Facts for Pembroke Homeowners
What energy savings can Pembroke homeowners expect from spray foam?
ENERGY STAR estimates homeowners save an average of 15% on heating and cooling costs, or about 11% on total energy costs, by air sealing and adding insulation in attics, floors over crawl spaces and basements. Spray foam does both jobs at once. Actual savings in Pembroke depend on how leaky the house is to start, which is why we measure it with a blower door test before and after the work.
How do open-cell and closed-cell foam compare for Pembroke houses?
Open-cell foam is light and vapor-permeable, at roughly R-3.6 per inch, and works well in above-grade walls and rooflines. Closed-cell foam is dense, at roughly R-6 per inch, and acts as a vapor retarder, so it is the better choice for rim joists, basement walls and anywhere moisture is a concern. The U.S. Department of Energy notes open-cell foam should not be used below ground level, and its Building America guide recommends at least 1.5 inches of closed-cell foam in cold-climate hybrid walls. Many Pembroke jobs use both.
How long before my family can return after spray foam goes in?
Yes, plan to be out. The EPA advises occupants to vacate during spray foam application and to wait until the foam has cured and the space has been ventilated and cleaned. Some manufacturers recommend about 24 hours before re-entry for professional two-component systems; we follow the specific product's guidance and tell you the exact timing before the job.
What energy code does Pembroke follow?
Pembroke follows the Stretch Code (effective 7/1/2011). For additions, gut renovations and new homes that means meeting stricter insulation and air-leakage targets, often verified with a blower door test or a HERS rating. Our Everett (371 Main St) office handles Pembroke jobs and can test the house with a blower door before and after the foam goes in.
What incentives apply to insulation work in Pembroke?
Mass Save offers 75–100% off approved insulation and air sealing improvements for 1- to 4-unit homes, plus 0% HEAT Loan financing of up to $25,000 for qualifying upgrades. Whether a specific spray foam measure qualifies depends on the program rules, so confirm before you start. The federal Energy Efficient Home Improvement Credit (25C) only covered property placed in service through 2025, so it no longer applies to new work.
Sources: U.S. Department of Energy (Building America Spray Foam Guide; Energy Saver), ENERGY STAR, Mass Save, IRS, U.S. EPA.
Spray Foam Types, R-Values and Vapor Control for Pembroke Homes
| Open-cell (about 0.5 lb density) | Closed-cell (about 2 lb density) | |
|---|---|---|
| R-value | About R-3.6 per inch | About R-6 per inch |
| Air barrier | Yes | Yes |
| Moisture vapor | Vapor-permeable (about 5–10 perms at 5 in.) | Class II vapor retarder (under 1 perm at 2 in.) |
| Below grade / basements | Not recommended | Yes |
| Adds wall strength | No | Yes, increases racking strength |
| Typical uses | Above-grade walls, rooflines, sound control | Foundation walls, rim joists, sills, cold-climate walls |
| Cost | Lower | Higher |
Is closed-cell spray foam a vapor barrier?
At about 2 inches thick, closed-cell foam is rated under 1 perm, which makes it a Class II vapor retarder under the residential building code (0.1 to 1.0 perm). That is not quite a Class I "vapor barrier" like polyethylene sheeting (0.1 perm or less), but it is low enough that most Pembroke walls don't need a separate plastic layer. Open-cell foam is vapor-permeable, at roughly 5 to 10 perms at 5 inches, so it may need a separate vapor retarder depending on the wall design.
How much R-value do I get from spray foam in my Pembroke walls?
Using DOE's typical values of about R-3.6 per inch for open-cell and R-6 per inch for closed-cell: a full 3.5-inch 2x4 cavity is about R-13 with open-cell or about R-21 with closed-cell, and a 5.5-inch 2x6 cavity is about R-20 with open-cell. Closed-cell is often sprayed 2 to 3 inches deep (about R-12 to R-18) and paired with another insulation. Because foam also seals air leaks, it usually performs better than its R-value alone suggests.
Can spray foam be left exposed in a Pembroke basement or attic?
In most cases, yes. The residential building code (IRC R316.4) requires foam plastic to be separated from living space by a thermal barrier of at least 1/2-inch drywall or an approved equivalent. In attics and crawl spaces entered only for service, an ignition barrier such as 1/4-inch plywood, 3/8-inch drywall or 1.5 inches of mineral fiber may be used instead, unless the specific foam product is approved to be left exposed. We confirm which applies before the job.
Can spray foam help prevent ice dams in Pembroke?
Ice dams form when heat escaping from the house warms the roof deck, melting snow that refreezes at the colder eaves. Massachusetts and DOE guidance both put air sealing the attic first, followed by insulation. Spray foam does both: on the attic floor it stops warm air from reaching the roof, and sprayed under the roof deck it creates an unvented, conditioned attic. It works best with a blower door test to find the leaks first.
Does spray foam add strength to framing?
Closed-cell foam is rigid once cured, and the Department of Energy's Building America guide reports that it substantially increases the racking strength of frame walls when used in the stud cavities. Open-cell foam is soft and flexible and does not add meaningful strength.
Is spray foam a good fit for a Pembroke basement or foundation?
Yes, with closed-cell foam. Department of Energy guidance calls for closed-cell spray foam on the inside of the foundation wall and along the sill. Open-cell foam should not be used below ground level because it can absorb water. Any water leaks or moisture problems in the basement have to be fixed first, and in finished or living space the foam must be covered with a code-approved thermal barrier such as 1/2-inch drywall.
Sources: U.S. DOE Building America Spray Foam Guide and Building America Solution Center; DOE Energy Saver; International Residential Code R316 and vapor retarder classes; Mass.gov ice dam guidance.
Existing Walls, Moisture and Crawl Spaces in Pembroke
Does spray foam work in a Pembroke crawl space?
DOE's Building America guidance favors an unvented, insulated crawl space: insulate the perimeter walls instead of the floor above, cover the ground with sealed 6-mil polyethylene, and provide a drying method such as a small exhaust fan or conditioned air supply (at least 1 CFM per 50 square feet of floor area, or 50 CFM). Closed-cell spray foam is a common way to insulate and air-seal those walls and the rim joist. Check with the Pembroke building department on radon, pest and fire-barrier requirements before you start.
Should a homeowner use a spray foam kit?
Small jobs are possible, but the EPA cautions that do-it-yourself applicators are often unaware of the inhalation and skin hazards. EPA describes three product types: one-component foam in cans for small gaps, low-pressure two-component kits for small areas, and high-pressure professional systems that require supplied-air respirators and protective clothing. Whole-wall, attic and basement jobs call for the professional system, and occupants should stay out until the foam has cured and the space is ventilated.
Will spray foam make my Pembroke home quieter?
It helps with sound that leaks through gaps, because foam seals the cracks and openings that let airborne noise in. Open-cell foam is softer and absorbs more sound than closed-cell. It is not a full soundproofing system on its own - walls facing heavy traffic usually also need added mass, such as an extra layer of drywall, for a big reduction.
Can spray foam be added to the finished walls of a Pembroke home?
Often, yes - but usually not with the same spray foam used on open framing. The Department of Energy lists foamed-in-place insulation and blown-in loose fill such as dense-pack cellulose as options for enclosed existing walls; both go in through small holes that are patched afterward. Standard two-part spray foam is sprayed into open cavities, so it fits best when walls are already open during a remodel, or at rim joists, attics and basements you can reach. What is already in the wall, and whether it has had moisture problems, decides which method is right.
Is there a mold risk with spray foam?
Not when the assembly is designed for our cold climate. Foam does not fix liquid water, so roof, plumbing and foundation leaks have to be repaired first. Closed-cell foam slows vapor and, at the right thickness, keeps the inside face of the sheathing warm; DOE's Building America guide calls for at least 1.5 inches of closed-cell in cold-climate hybrid walls for that reason. Open-cell foam lets vapor pass, so the wall needs a drying path or a separate vapor retarder depending on the design.
Sources: U.S. DOE Energy Saver (insulation types); DOE Building America Spray Foam Guide and Solution Center (unvented crawlspaces); U.S. EPA (spray polyurethane foam product types).
Frequently Asked Questions
How much does spray foam insulation cost?
Cost depends on the foam type, the square footage, and how many inches of thickness the assembly needs, so a garage, an attic, and a whole-home retrofit all price differently. Rather than quote a number that won't fit your home, we assess the Pembroke project and give you a written, itemized estimate. Request a quote and we'll walk you through the options.
Why do some people remove or worry about spray foam insulation?
Most concerns trace back to foam that was installed at the wrong thickness, in the wrong mix ratio, or without proper ventilation — which can lead to odor or poor curing. Correctly installed foam from a certified crew performs reliably for decades. On every Pembroke job we verify substrate conditions, mix ratios, and thickness, and document the R-values so the assembly is done right the first time.
What R-value is required for spray foam in Massachusetts?
Massachusetts follows Climate Zone 5 requirements. Above-grade walls generally need about R-20 (or R-13 cavity plus R-5 continuous), attics and ceilings call for roughly R-49 to R-60, floors over unconditioned space about R-30, and basement or crawlspace walls around R-15 continuous. We size the foam on every Pembroke project to hit the value your assembly needs to pass code.
How much insulation does an attic need?
Massachusetts code targets about R-49 to R-60 in attics. Because attics are usually the biggest source of heat loss, they are often the most cost-effective place to add insulation first.
What is the difference between open-cell and closed-cell foam?
Closed-cell foam is denser, delivers about R-6 to R-7 per inch, and acts as an air and vapor barrier — good for rim joists, basements, and roof decks. Open-cell is lighter, about R-3.5 to R-3.8 per inch, vapor-permeable, and often used in walls and attics.
What R-value do you get from 2 inches of closed-cell spray foam?
At about R-6.5 to R-7 per inch, two inches of closed-cell foam gives roughly R-13, and that layer also air-seals the cavity and controls vapor. On many Pembroke walls we pair a 2-inch closed-cell flash with a lower-cost fill to reach the full target economically.
How do you reach R-30 in a wall with spray foam?
The most cost-effective route is a flash-and-fill assembly: about 2 inches of closed-cell foam (≈ R-13) against the sheathing, then the rest of the cavity filled with open-cell, dense-pack cellulose, or batt (≈ R-16 to R-18). In a standard Pembroke 2x6 wall that combination lands right around R-30.
Does Mass Save cover spray foam insulation?
Mass Save is a real Massachusetts efficiency program that Pembroke homeowners can explore. It typically funds a no-cost home energy assessment and offers incentives toward weatherization and air sealing; coverage for spray foam specifically can vary and often depends on the assessment, so we help you understand what your project may qualify for.
Can a converted pond cottage in Pembroke be insulated well?
Yes. The usual steps are insulating the floor or crawl space and the roof slope and sealing the rim joist, after we check for moisture.
Does a Pembroke building permit need a HERS rating?
Pembroke lists HERS ratings among the supporting documents for some permit applications, which usually applies to new homes and large renovations. HEEC can provide the rating.
Mass Save®-Listed HERS Rater
U.S. DOE Efficient New HomeTrusted Partner — Verified
ENERGY STAR®Partner
Phius CertifiedPassive House Verifier
ICCMember★★★★★136 Google
Reviews
The Phius Certified Verifier logo is used under license from Phius.
HERS Ratings Across Pembroke and Nearby Communities
Home Energy Efficiency Consultants rates new homes, additions, and major renovations throughout Pembroke — including Pembroke Center, Bryantville, and North Pembroke. Every Pembroke project is filed with the Town of Pembroke Building Department, and we handle the energy model, blower door and duct leakage testing, and the compliance paperwork from start to finish.
We also serve the communities right around Pembroke, including Hanover, Marshfield, Duxbury, Kingston, and Hanson. Our Somerville office at 519 Broadway is the closest of our four Massachusetts locations — see our Somerville office or call (617) 501-6788 to get a Pembroke rating on the schedule.
