Blower Door Testing Danvers MA - Quick Facts
Local energy code in Danvers
- Danvers is a Stretch Code community - the statewide baseline for new construction and major renovations. IECC Climate Zone 5A.
- Massachusetts has three energy-code levels - base (2021 IECC), Stretch, and Specialized (Opt-In) - and Danvers is on the Stretch Code.
Blower door requirement in Danvers
- New homes in Danvers must test at 3.0 ACH50 or tighter under the Massachusetts Stretch Code.
- Air-leakage testing is mandatory, measured with a calibrated blower-door fan to the RESNET / ASTM protocol - there is no inspection-only substitute for the result.
- Companion duct leakage limit: 4 CFM25 per 100 sq ft of conditioned floor area when ducts run outside conditioned space.
- Same-day preliminary results; final report in 24-48 hours, filed with the Danvers building department.
Mass Save rebates for Danvers (2026)
- A tight result unlocks Mass Save all-electric incentives ($7,500 to $25,000 per new single-family home); an all-electric renovation testing at 3.0 ACH50 or better reaches the Level 2 tier, up to $30,000.
- Incentives require a Mass Save-approved, RESNET-certified HERS rater.
RESNET-certified · 15,000+ ratings completed · 5.0 stars across 135 Google reviews · (617) 501-6788
Blower Door Testing Danvers MA
Certified blower door testing in Danvers - we measure your home's air-tightness in ACH50, pinpoint leaks, and document a passing result for your building permit.
Air-tightness at a glance
Blower Door Testing Danvers MA
A blower door test is the code-required way to prove how airtight a home in Danvers really is. A calibrated fan depressurizes the house to 50 Pascals so we can measure exactly how much air leaks through the envelope, reported as air changes per hour (ACH50). New construction must reach 3.0 ACH50 or lower, while remodels are allowed up to 5.0 ACH50.
| Project type | Max ACH50 | Notes |
|---|---|---|
| New construction | 3.0 or lower | Mandatory blower-door test under R402.4.1.2 |
| Remodel / alteration | 5.0 | Realistic target for existing assemblies |
| Addition < 1,000 sq ft | Exempt* | May be exempt from testing (R502.3.1) |
| Passive House / Specialized | 0.6 | Whole-building test, Phius/PHI protocol |
*Confirm with your local building department. Requirements per the 2025 MA Stretch Energy Code Technical Guidance.
How Blower Door Testing Works in Danvers
The fan mounts in an exterior doorway and holds the home at a fixed 50-Pascal pressure difference - about what a 20 mph wind would exert. The airflow required to maintain that pressure, in CFM, converts to ACH50 using the home's conditioned volume.
The code converts the result to Q50 (CFM at 50 Pa) with Q50 = (Volume × ACH50) ÷ 60. A 2,700 sq ft home at 2 ACH50 works out to roughly 810 CFM50.
Keeping Heat In During Danvers Cold Spells
During a New England cold snap the stack effect goes to work: warm indoor air rises and slips out near the top of the house, and that pulls cold outdoor air in through gaps down low. The colder it gets, the harder this effect pushes - so a leaky home loses the most heat exactly when it can least afford to.
A tight, tested envelope shrinks the infiltration share of your heating load. That lets the equipment keep up during cold spells, holds rooms at a steadier temperature between cycles, and often lets a designer right-size the heating system rather than oversizing it to cover leakage.
Lower heating load
Less infiltration means a smaller winter heat-loss load and equipment that can keep up.
Retain paid-for heat
Warm air stays in the living space instead of escaping out the top of the house.
Steadier comfort
Fewer cold-floor drafts and a temperature that holds between heating cycles.
Where Danvers Homes Leak Air
During depressurization the leaks are exaggerated, making them easy to find. In Essex County's older housing stock the usual suspects are rim joists, top plates, attic hatches, recessed lights, and penetrations for plumbing and wiring. Coastal and exposed sites feel wind-driven infiltration most, so a tight, verified envelope pays back quickly here.
Best Fit for Projects Like
- Gut renovations and deep-energy retrofits
- Homes chasing Passive House or net-zero targets
- Pre-drywall diagnostic testing for builders
- New single-family homes needing a code compliance test
- Additions over 1,000 sq ft that trigger testing
Blower Door Testing Danvers MA Facts
Warmer floors, fewer drafts
Cutting the cold air drawn in low means warmer floors and fewer cold-corner drafts, which is often the comfort difference people notice first after air sealing.
Helping heat keep up
Sealing the envelope shrinks the infiltration portion of the heating load, so the furnace or heat pump can actually hold temperature through a cold spell instead of running flat-out and falling behind.
Air leakage and heating cost
Uncontrolled air leakage can raise a home's heating and cooling costs by 30% or more, which is why the code treats envelope tightness as a mandatory measure.
What a blower door measures
A blower door is a calibrated fan sealed into an exterior doorway. It pressurizes and depressurizes the home to 50 Pascals so the exact volume of leaking air can be measured in cubic feet per minute.
Trusted for Blower Door Testing Danvers MA
I am building a 5-unit conversion in East Boston and used this HERS rating company. Some of the most reasonable, knowledgeable HERS raters I have dealt with in the greater Boston area.
I worked with this HERS rating company in South Boston on a remodel project and was able to get back 30,000 in rebates.
I wanted to express my satisfaction working with this excellent professional. I highly recommend Dominic.
Our Massachusetts Service Locations
Serving clients from our Massachusetts locations in Everett, Somerville, and Framingham.
Everett Location
371 Main St
Everett, MA 02149
Somerville Location
519 Broadway
Somerville, MA 02145
Framingham Location
68 South St
Framingham, MA 01702
FAQ About Blower Door Testing Danvers MA
What documentation do I receive?
You receive the measured ACH50 result on a RESNET/HERS-style report suitable for the building department, plus notes on any sealing performed.
How long does a blower door test take?
For a typical single-family home the test itself usually takes well under an hour once the fan is set up and the home is prepared.
What is a blower door test?
It is a diagnostic that measures how airtight a building is. A calibrated fan mounted in a doorway pressurizes or depressurizes the home to 50 Pascals and measures the airflow needed to hold that pressure, which is reported as ACH50.
Does a tighter house need mechanical ventilation?
Yes. A tight home relies on balanced mechanical ventilation for fresh air, and the code sizes that ventilation (R403.6 / ASHRAE 62.2) using your verified blower-door rate.
How is ACH50 converted to CFM?
The code uses Q50 = (conditioned volume x ACH50) / 60. For example, a 2,700 sq ft home with 9 ft ceilings at 2 ACH50 equals about 810 CFM50.
Do you work with builders and homeowners?
We work with builders, remodelers, designers, and homeowners - from single tests for permit sign-off to pre-drywall diagnostics that catch problems early.
Get Started With Blower Door Testing Danvers MA
Book a certified blower door test and get a permit-ready air-tightness report. Call 617-501-6788.
HERS Ratings Across Danvers and Nearby Communities
Home Energy Efficiency Consultants rates new homes, additions, and major renovations throughout Danvers — including Danvers Center, Danversport, Tapleyville, and Putnamville. Every Danvers project is filed with the Town of Danvers Building Department, and we handle the energy model, blower door and duct leakage testing, and the compliance paperwork from start to finish.
We also serve the communities right around Danvers, including Peabody, Beverly, Middleton, Topsfield, and Salem. Our Everett office at 371 Main St is the closest of our four Massachusetts locations — see our Everett office or call (617) 501-6788 to get a Danvers rating on the schedule.
More Massachusetts Towns We Serve
Certified HERS ratings, blower door testing and energy code compliance across all 351 Massachusetts cities and towns.
