Blower Door Testing Bridgewater MA
Certified blower door testing in Bridgewater - we measure your home's air-tightness in ACH50, pinpoint leaks, and document a passing result for your building permit.
Air-tightness at a glance
Blower Door Testing Bridgewater MA
A blower door test is the code-required way to prove how airtight a home in Bridgewater really is. A calibrated fan depressurizes the house to 50 Pascals so we can measure exactly how much air leaks through the envelope, reported as air changes per hour (ACH50). New construction must reach 3.0 ACH50 or lower, while remodels are allowed up to 5.0 ACH50.
| Project type | Max ACH50 | Notes |
|---|---|---|
| New construction | 3.0 or lower | Mandatory blower-door test under R402.4.1.2 |
| Remodel / alteration | 5.0 | Realistic target for existing assemblies |
| Addition < 1,000 sq ft | Exempt* | May be exempt from testing (R502.3.1) |
| Passive House / Specialized | 0.6 | Whole-building test, Phius/PHI protocol |
*Confirm with your local building department. Requirements per the 2025 MA Stretch Energy Code Technical Guidance.
How Blower Door Testing Works in Bridgewater
The fan mounts in an exterior doorway and holds the home at a fixed 50-Pascal pressure difference - about what a 20 mph wind would exert. The airflow required to maintain that pressure, in CFM, converts to ACH50 using the home's conditioned volume.
The code converts the result to Q50 (CFM at 50 Pa) with Q50 = (Volume × ACH50) ÷ 60. A 2,700 sq ft home at 2 ACH50 works out to roughly 810 CFM50.
Keeping Heat In During Bridgewater Cold Spells
Air-leakage heat loss grows with the gap between indoor and outdoor temperature, which is why a drafty home feels worst in a deep freeze. Warm air you have paid to heat escapes high, cold air rushes in low, and the heating system ends up chasing a load that keeps climbing as the temperature drops.
A tight, tested envelope shrinks the infiltration share of your heating load. That lets the equipment keep up during cold spells, holds rooms at a steadier temperature between cycles, and often lets a designer right-size the heating system rather than oversizing it to cover leakage.
Lower heating load
Less infiltration means a smaller winter heat-loss load and equipment that can keep up.
Retain paid-for heat
Warm air stays in the living space instead of escaping out the top of the house.
Steadier comfort
Fewer cold-floor drafts and a temperature that holds between heating cycles.
Where Bridgewater Homes Leak Air
During depressurization the leaks are exaggerated, making them easy to find. In Plymouth County's older housing stock the usual suspects are rim joists, top plates, attic hatches, recessed lights, and penetrations for plumbing and wiring. Coastal and exposed sites feel wind-driven infiltration most, so a tight, verified envelope pays back quickly here.
Best Fit for Projects Like
- Pre-drywall diagnostic testing for builders
- Custom and high-performance builds
- Homes chasing Passive House or net-zero targets
- Certificate-of-occupancy sign-off
- Mass Save incentive and rebate projects
Blower Door Testing Bridgewater MA Facts
Moisture protection
Controlling air movement also controls the moisture that rides with it, protecting insulation and framing from condensation and mold over the life of the home.
Remodel threshold
Remodels and alterations to existing homes are held to a more achievable 5.0 ACH50, recognizing that older assemblies are harder to seal than new framing.
What a blower door measures
A blower door is a calibrated fan sealed into an exterior doorway. It pressurizes and depressurizes the home to 50 Pascals so the exact volume of leaking air can be measured in cubic feet per minute.
Savings from air sealing
Reducing leakage from about 10 ACH50 to 5 ACH50 can cut heating and cooling energy use by roughly 15 to 25 percent in a typical home.
Trusted for Blower Door Testing Bridgewater MA
I had an excellent experience. Friendly, knowledgeable, and very responsive. I will definitely be coming back.
When I was going to pull my building permit I was confused about documentation to meet the Massachusetts stretch energy code, but Home Energy was extremely helpful in explaining the HERS rating process and helping me apply for Mass Save rebates.
Five stars isn't enough. The team at Home Energy Efficiency Consultants LLC goes above and beyond every time. They're the gold standard for HERS ratings in Massachusetts.
Our Massachusetts Service Locations
Serving clients from our Massachusetts locations in Everett, Somerville, and Framingham.
Everett Location
371 Main St
Everett, MA 02149
Somerville Location
519 Broadway
Somerville, MA 02145
Framingham Location
68 South St
Framingham, MA 01702
FAQ About Blower Door Testing Bridgewater MA
What ACH50 does new construction need to pass?
New residential construction in Massachusetts must measure 3.0 ACH50 or lower. Many high-performance homes come in well below that figure.
Do you work with builders and homeowners?
We work with builders, remodelers, designers, and homeowners - from single tests for permit sign-off to pre-drywall diagnostics that catch problems early.
How tight is a Passive House?
Passive House projects on the Specialized Code path target around 0.6 ACH50 - roughly ten times tighter than base code - verified with a whole-building blower-door test.
Does a tighter house need mechanical ventilation?
Yes. A tight home relies on balanced mechanical ventilation for fresh air, and the code sizes that ventilation (R403.6 / ASHRAE 62.2) using your verified blower-door rate.
What happens if my home fails the test?
The rater locates the leaks with smoke, an infrared camera, or by feel, those areas are sealed, and the home is retested until it meets the target.
Will a tighter home lower my heating load?
Yes. Infiltration is one of the largest parts of a winter heat-loss calculation. Reducing leakage directly shrinks the heating load, which can mean right-sized equipment, lower bills, and a home that holds temperature better in cold weather.
Get Started With Blower Door Testing Bridgewater MA
Book a certified blower door test and get a permit-ready air-tightness report. Call 617-501-6788.
