Blower Door Testing Georgetown MA
Certified blower door testing in Georgetown - we measure your home's air-tightness in ACH50, pinpoint leaks, and document a passing result for your building permit.
Air-tightness at a glance
Blower Door Testing Georgetown MA
A blower door test is the code-required way to prove how airtight a home in Georgetown really is. A calibrated fan depressurizes the house to 50 Pascals so we can measure exactly how much air leaks through the envelope, reported as air changes per hour (ACH50). New construction must reach 3.0 ACH50 or lower, while remodels are allowed up to 5.0 ACH50.
| Project type | Max ACH50 | Notes |
|---|---|---|
| New construction | 3.0 or lower | Mandatory blower-door test under R402.4.1.2 |
| Remodel / alteration | 5.0 | Realistic target for existing assemblies |
| Addition < 1,000 sq ft | Exempt* | May be exempt from testing (R502.3.1) |
| Passive House / Specialized | 0.6 | Whole-building test, Phius/PHI protocol |
*Confirm with your local building department. Requirements per the 2025 MA Stretch Energy Code Technical Guidance.
How Blower Door Testing Works in Georgetown
The fan mounts in an exterior doorway and holds the home at a fixed 50-Pascal pressure difference - about what a 20 mph wind would exert. The airflow required to maintain that pressure, in CFM, converts to ACH50 using the home's conditioned volume.
The code converts the result to Q50 (CFM at 50 Pa) with Q50 = (Volume × ACH50) ÷ 60. A 2,700 sq ft home at 2 ACH50 works out to roughly 810 CFM50.
Keeping Heat In During Georgetown Cold Spells
In winter the biggest enemy of a warm home is often invisible air movement. The stack effect drives heated air out through the top of the envelope and draws frigid air in near the floor, robbing heat all season - Cornell extension research describes it plainly as the effect that steals warmth from your home every winter.
Once the leaks are found and sealed, the home retains heat far longer between heating cycles. Floors stay warmer, temperatures hold steady on windy nights, and the reduced heating load shows up directly on winter utility bills.
Lower heating load
Less infiltration means a smaller winter heat-loss load and equipment that can keep up.
Retain paid-for heat
Warm air stays in the living space instead of escaping out the top of the house.
Steadier comfort
Fewer cold-floor drafts and a temperature that holds between heating cycles.
Where Georgetown Homes Leak Air
During depressurization the leaks are exaggerated, making them easy to find. In Essex County's older housing stock the usual suspects are rim joists, top plates, attic hatches, recessed lights, and penetrations for plumbing and wiring. Coastal and exposed sites feel wind-driven infiltration most, so a tight, verified envelope pays back quickly here.
Best Fit for Projects Like
- Pre-drywall diagnostic testing for builders
- Additions over 1,000 sq ft that trigger testing
- New single-family homes needing a code compliance test
- Mass Save incentive and rebate projects
- Multi-family and townhouse units
Blower Door Testing Georgetown MA Facts
Right-sizing equipment
A verified-tight envelope lets a designer right-size the furnace, boiler, or heat pump instead of oversizing for leakage - lowering both equipment cost and running cost.
Retaining the heat you paid for
A tight, tested envelope keeps the warm air you have already paid to heat inside the living space rather than letting it leak out the top of the house.
Cold snaps magnify leakage
Infiltration heat loss scales with the indoor-outdoor temperature difference, so a leaky envelope bleeds the most heat exactly when you need it most - during a deep freeze.
Quiet, fast, non-destructive
A typical single-family blower door test is non-destructive and usually wraps up in well under an hour once setup is complete.
Trusted for Blower Door Testing Georgetown MA
This company does all my inspections. I use this company a lot and highly recommend them.
One of the most reliable companies that I've worked with in Somerville, Massachusetts.
I am building a 5-unit conversion in East Boston and used this HERS rating company. Some of the most reasonable, knowledgeable HERS raters I have dealt with in the greater Boston area.
Our Massachusetts Service Locations
Serving clients from our Massachusetts locations in Everett, Somerville, and Framingham.
Everett Location
371 Main St
Everett, MA 02149
Somerville Location
519 Broadway
Somerville, MA 02145
Framingham Location
68 South St
Framingham, MA 01702
FAQ About Blower Door Testing Georgetown MA
How does air sealing help during a cold spell?
In winter the stack effect drives warm air out the top of the house and pulls cold air in low down, and it gets stronger the colder it is. A tight, tested envelope blunts that effect, so you retain more of the heat you have paid for and your heating system can keep up during a deep freeze.
Do you work with builders and homeowners?
We work with builders, remodelers, designers, and homeowners - from single tests for permit sign-off to pre-drywall diagnostics that catch problems early.
Can a blower door test find where my home is drafty?
Yes. Depressurizing the home exaggerates the leaks so a rater can pinpoint exactly where outdoor air is entering, which guides targeted air sealing.
Does a tighter house need mechanical ventilation?
Yes. A tight home relies on balanced mechanical ventilation for fresh air, and the code sizes that ventilation (R403.6 / ASHRAE 62.2) using your verified blower-door rate.
What does the 50 Pascal test pressure represent?
Fifty Pascals is roughly the pressure a 20 mph wind exerts on the whole building. Testing at a fixed pressure makes the result repeatable regardless of the weather that day.
Will a tighter home lower my heating load?
Yes. Infiltration is one of the largest parts of a winter heat-loss calculation. Reducing leakage directly shrinks the heating load, which can mean right-sized equipment, lower bills, and a home that holds temperature better in cold weather.
Get Started With Blower Door Testing Georgetown MA
Book a certified blower door test and get a permit-ready air-tightness report. Call 617-501-6788.
